• Athanasiou Diakou 5, Pallini, Greece.

Carrier Marine

  1. Home
  2. Carrier Marine

Marine Compressors

5F/5H Open-Drive Reciprocating Compressor

20 to 346 Nominal CFM.

  • Automatic unloaded starting, expensive high-torque motors are unnecessary, reducing initial expense.
  • High-efficiency motor can further increase efficiency of 5F and 5H compressors.
  • Crankcase casting, cylinder head, and valve plate designs allow for a smooth, unrestricted refrigerant flow.
  • Refined, two-piece shaft seal assembly virtually eliminates seal leakage for maximum reliability over a wide temperature range.
  • Efficient crankcase heater design prevents accumulation of liquid refrigerant in the crankcase during shutdown, dilution of the compressor oil supply.
  • As suction pressure changes, capacity control automatically reduces compressor capacity to as low as 35% of full-design load, reducing horsepower requirements as demand changes. Part-load operation increases energy efficiency, reducing utility bills.
  • Large-capacity, manually reversible oil pump, automatic pressure regulator, and oil-filtering system provide positive pressure lubrication, extending life.
  • Suction gases flow around cylinder sleeve to keep the cylinder cool, reducing cylinder wear.
  • Greater operating efficiencies by running an oversized compressor at a reduced RPM.

06D/06E Semi-Hermetic Reciprocating Compressor

8 to 99 Nominal CFM.

  • High-flow, automatically reversible oil pump provides positive-displacement oil lubrication.
  • Crankcase venting system equalizes pressure during startup and assures oil return to sump.
  • Oversize sump holds extra oil in crankcase to prevent levels dropping below safe lubrication range during flooded starts.
  • Contoured pistons lower cylinder clearances to increase compressor capacity and efficiency.
  • High-efficiency valves provide increased refrigerant flow and lower pressure drops.
  • Electronic oil-pressure switch

05T/06T Twin-Screw Compressor

33 to 88 Nominal CFM
05T – Open-Drive
06T – Semi-Hermet

  • No suction or discharge valves provide smooth, quiet, vibration-free operation.
  • Low-clearance screw design for lower oil-circulation rates.
  • Ideal for variable-speed applications.
  • Precision long-life bearings.
  • Capacity control.
  • Economizer-cooled motor provides high-efficiency operation.
  • Uses O-ring seals.
  • Compatible with many different refrigerant/oil combinations.
  • Internal discharge check valve.
  • No oil pump.
  • Two-step Vi for low-temperature models to maximize efficiency over a wide operating rang.

05K/05G Open-Drive Reciprocating Compressor

—

  • Superior efficiency significantly reduces horsepower drain, reduces maintenance, extends life, saves fuel.
  • Exclusive balanced cylinder design minimizes torque pulsations for smoother operation, less wear.
  • Extended maintenance, lower operating speeds, lower vibrations, and less wear mean less maintenance and lower operating costs.
  • Larger capacity self-priming, reversible oil pump provides dependable oil flow under cold or flooded startup conditions and ample pressure at low rpm.
  • Higher capacity, efficiency at speeds at least 30% lower.
  • Housing-mounted clutch and larger clutch bearing provide longer life.
  • Low oil-circulation rate of less than 1% for greater operating efficiency.
  • Exclusive compressor unloading saves fuel, increases efficiency, eliminates coil freezing, for uniform temperature distribution.
  • Industry-leading parts-and-labor warranty

90M Marine Packaged Cooling Unit

3 to 10 Nominal Tons (10.5 to 35.1 kW)
90MA – Seawater cooled
90MU – Condenserless

The 90M Marine Packaged Cooling Unit is specially designed to fit easily aboard a ship or drill rig, wherever it is needed. On the bridge, in the control room, or in computer areas where environmental control is essential, the 90M keeps people comfortable and protects sensitive controls and navigation instruments.

  • Standard models available with R-134a, R-404A, or R-407C.
  • Compact cabinet fits any working environment.
  • Free-blow or ducted supply air.
  • Cools, heats, dehumidifes, and filters air; prevents mildew.
  • Attractive design saves space and complements any decor.
  • Thermostat controls located for accessibility.
  • Black epoxy paint on interior sheet metal for added corrosion resistance.
  • Return air panel is slotted with an extruded handle for easy service access.
  • Cleanable aluminum mesh return air filters.
  • Quick sensing elements prevent compressor trouble before it starts
  • Compressor crankcase heaters prevent flooded starts and dilution of oil by refrigerant.
  • Includes seawater regulating valve to maintain discharge pressure.
  • Meets UL requirements. USCG approval not needed.

Chillers

30HX Evergreen®

High-Efficiency
Indoor Liquid Screw Chillers
70 to 265 Nominal Tons
30HXA – Condenserless
30HXC – Water-cooled

The 30HX units are high-efficiency, indoor water-cooled or condenserless chillers. The units have a quiet, low-vibration design featuring screw compressors. The 30HX chillers are compact enough to fit through a standard door, making them great replacement units.

  • Chlorine-free HFC-134a refrigerant
  • Low energy consumption during part load and full load operation
  • 208/230 v, 230 v, 460 v, 575 v operational voltages available
  • Wye-delta start is standard on 208/230 v and 230 v 50/60 Hz units (factory-installed option for all other units)
  • Leaving-fluid temperature directly controlled to within 0.5° F (0.3° C)
  • Entering-fluid temperature continuously monitored to detect flow or load changes
  • Compatible with Carrier Comfort Network® (CCN) communication link.
  • Low voltage control circuits
  • Short cycle protection
  • Dual chiller control
  • Mechanically cleanable condenser and cooler (30HXC)
  • Hermetic twin screw compressors
  • Electronic refrigerant gages
  • Chilled water flow switch
  • Temperature reset from return fluid
  • Alarm contacts
  • Fits through standard doorway
  • Modular construction
  • ON/OFF control switch
  • Discharge and liquid line shutoff valves
  • Accessible service information including suction and discharge pressure and temperature using Navigator™ display module
  • Moisture indicating sight glass
  • Filter drier
  • Fits through standard doorway
  • Modular construction
  • ON/OFF control switch
  • Fits through standard doorway
  • Modular construction
  • Fits through standard doorway
  • Single point electrical connection
  • Easy connections for remote condensers (30HXA)
  • Neoprene vibration isolators (field-installed accessory)
  • One year from start-up or 18 months from shipment

30XA AQUAFORCE®

Outdoor, Air-Cooled Liquid Chiller
with R-134a Refrigerant
80 to 500 Nominal Tons

AquaForce 30XA chillers were designed from the ground up to meet the efficiency demands of today and the future by providing premium air-cooled chiller packages for contractors, consulting engineers and building owners. Value-added features include rotary screw compression, R-134a HFC refrigerant, a quiet AeroAcoustic™ fan system, easy to use ComfortLink™ controls, microchannel condenser coil technology, and an optional integrated hydronic pump package with or without VFD.

  • Full-load EER values up to 10.9
  • IPLV values up to 15.4
  • ASHRAE 90.1 complaint
  • AHRI certified
  • Easy to use controls
  • Low sound levels
  • AeroAcoustic fan system
  • Operation from -20 F to 125 F ambient conditions
  • High-efficiency screw compressors
  • Novation® microchannel heat exchanger (MCHX) condenser coils
  • E-coated Novation microchannel heat exchanger (MCHX) condenser coils (factory-installed option)
  • Hydronic pump package, available with or without VFD on sizes 090-160 (factory-installed option)
  • Energy Management Module minimizes chiller energy consumption (factory-installed option or field-installed accessory)
  • Non-fused disconnect switch (factory-installed option)
  • Minimum load control (factory-installed option, field-installed accessory)
  • EXV (Electronic Expansion Valve)
  • Low ambient head pressure control (factory-installed option or field-installed accessory)
  • Wye-delta starter available (factory-installed option)
  • ComfortLink™ controls with Touch Pilot™ or Navigator™ display
  • BACnet* Communication (factory-installed option) or BACnet and LON translator control (factory-installed option or field-installed accessory)
  • EXV (Electronic Expansion Valve)
  • DX Cooler (factory-installed option)
  • ASME constructed evaporators
  • ETL (and ETL Canada) listed
  • Manufacturing facility registered to ISO 9001 manufacturing quality standard
  • Minimum of 2 independent refrigerant circuits
  • Factory full-load run tested
  • Heavy-gage galvanized steel frame
  • Security grilles (factory-installed option or field-installed accessory)
  • Hail guards/Privacy screen choices (factory-installed option or field-installed accessory)
  • Low ambient head pressure control (factory-installed option or field-installed accessory)
  • E-coated MCHX coil protection (factory-installed option)
  • Redundant pump with VFD-compatible motor available with hydronic pump package (sizes 090-160; factory-installed option)
  • Coil corrosion coatings available on all coil types (factory-installed option)
  • High short circuit current rating (factory-installed option)
  • EXV (Electronic Expansion Valve)
  • Over 15 diagnostic functions
  • Permanently lubricated fan motor bearings
  • Compressor suction service valves (factory-installed option)
  • Microchannel condenser coils with inherent corrosion resistance and offering simplified cleaning (factory-installed option)
  • Unit-mounted, non-fused disconnect (factory-installed option)
  • Remote service port for easier machine diagnostics (factory-installed option or field-installed accessory)
  • Factory charged with R-134a refrigerant
  • All-in-one package
  • Integrated hydronic pump package with or without VFD (sizes 090-160; factory-installed option)
  • GFI (ground fault interrupter) convenience outlet (factory-installed option or field-installed accessory)
  • Remote cooler kit (field-installed accessory)
  • Single or dual-point electrical connections available (factory-installed option)
  • Control transformer (factory-installed option)
  • Extended warranty packages available
  • 3-year coil parts warranty on Novation microchannel heat exchanger
  • One year from start-up or 18 months from shipment limited warranty
  • Standard Warranty
  • Circuit setter provided with optional pump package (factory-installed option)
  • Structurally robust base

19XR EVERGREEN®

High-Efficiency
Hermetic Centrifugal Chiller 19XR
200 to 1,500 Nominal Tons (703 to 5275 kW)
19XRV with Variable frequency Drive
200 to 1,450 Nominal Tons (703 to 5100 kW)

The Evergreen 19XR,XRV centrifugal chillers achieve energy efficiency levels using proven technology designed specifically for chlorine-free refrigerant. This combination ensures the most cost-effective, reliable solution for today’s comfort cooling and process cooling applications. Carrier’s Evergreen chillers offer the best value in high-efficiency, chlorine-free centrifugal HVAC chillers.

  • Low voltage control circuits
  • Single-stage positive-pressure compressor
  • ASME constructed heat exchangers
  • Compatible with Carrier Comfort Network® (CCN) communication link
  • Multilingual display
  • Aerodynamically contoured impeller
  • Low energy consumption during part load and full load operation
  • Hermetic compressor motor
  • Chlorine-free HFC-134a refrigerant
  • IPLV to 0.35 (19XRV)
  • Lowest industry refrigerant leakage rate at less than 0.1%
  • Hermetically sealed compressor, motor, and transmission
  • Automated controls may be tested before start-up
  • Refrigerant-cooled, unit-mounted variable frequency drive (19XRV)
  • Password protected extensive service menu with built-in diagnostic capabilities, troubleshooting, and corrective action recommendations for preset alarms
  • Alarm and alert files maintain the last 25 time and date stamped messages in memory
  • Configuration data backup with non-volatile memory
  • Thermistor-type temperature sensor with quick connects in each water nozzle
  • Refrigerant isolation valves for in-chiller refrigerant storage (factory-installed option)
  • Unit-mounted pumpout unit for storing refrigerant inside the chiller during servicing (factory-installed option)
  • Service contract available
  • Extended warranties available
  • Refrigerant warranty 5 years from date of manufacture
  • One year from start-up or 18 months from shipment
  • Standard Warranty
  • Automated controls test on startup
  • Compressor, motor, and transmission hermetically sealed
  • Less than 0.1% refrigerant leakage rate – lowest in the industry
  • Refrigerant cooled unit mounted VFD
  • Low voltage control circuits

30RAP AQUASNAP®

Outdoor, Air-Cooled Liquid Chiller
with Puron® Refrigerant (R-410A)
10 to 150 Nominal Tons

The AquaSnap 30RAP chiller is an effective all-in-one package that is easy to install and own. The chiller costs less to purchase and install than other chillers in its class, and operates quietly and efficiently. Value-added features include rotary scroll compression with optional digital compressor (010 to 090 units), Puron refrigerant (R-410A), a low-sound AeroAcoustic™ fan system, easy to use ComfortLink™ controls, microchannel condenser coil technology, optional integrated hydronic pump package, and an accessory fluid storage tank (sizes 010-060 only).

  • Full-load EER values up to 10.5
  • IPLV values up to 15.9
  • ASHRAE 90.1 compliant
  • AHRI 550/590 certified
  • High-efficiency rotary scroll compressors
  • Non-ozone depleting Puron refrigerant (R-410A)
  • Digital compressor unloading (factory-installed option for 010-090 units)
  • Standard uncoated or optional e-coated Novation® microchannel heat exchanger (MCHX) condenser coils (factory-installed option)
  • Hydronic pump package (factory-installed option) with optional VFD on sizes 070-150
  • Low-sound AeroAcoustic fans
  • Value option, propeller-type fans (factory-installed option)
  • Hot gas bypass (not available on sizes 010 and 015; factory-installed option)
  • Fluid loop storage tank (field-installed accessory on sizes 010-060)
  • Compressor blankets (factory-installed option)
  • Non-fused disconnect switch (factory-installed option) (not available with dual point power)
  • Operation from -20 to 120 F ambient temperature (factory-installed option or field-installed accessory on sizes 018-150 with low ambient head pressure control)
  • ComfortLink™ controls with scrolling marquee display module
  • Navigator™ and Touch Pilot™ displays (field-installed accessories)
  • Energy management module (factory-installed option or field-installed accessory)
  • BACnet™ communication (factory-installed option) or BACnet and LON (local operating network) translator control (field-installed accessory)
  • EXV (electronic expansion valve)
  • ETL (and ETL, Canada) listed
  • Manufacturing facility registered to ISO 9001 manufacturing quality standard
  • Galvanized steel cabinet with baked enamel powder or pre-painted finish on exterior panels passes 500-hour salt-spray test in accordance with the ASTM B-117 Standard
  • Heavy-gage galvanized steel frame
  • 2 independent refrigerant circuits (sizes 035-150)
  • Factory full-load run tested
  • Security grilles/hail guards (factory-installed option)
  • High and low-pressure protection
  • Compressor overload protection
  • E-coated MCHX coil protection (factory-installed option)
  • Self contained 24-v CCN (Carrier Comfort Network™) controls including transformer
  • Low ambient head pressure control (factory-installed option or field-installed accessory)
  • Redundant pump available with hydronic package (factory-installed option)
  • High short circuit current rating (factory-installed option) (not available with dual point power)
  • Hermetic scroll compressors and outdoor fan circuits are protected by circuit breakers or fuses
  • EXV (electronic expansion valve)
  • Over 15 diagnostic functions
  • Permanently lubricated fan motor bearings
  • Microchannel condenser coils offer simplified cleaning
  • Unit-mounted, non-fused disconnect (factory-installed option) (not available with dual point power)
  • Factory-charged with Puron refrigerant (R-410A)
  • All-in-one package
  • Integrated hydronic pump package (factory-installed option)
  • Fluid loop expansion tank (sizes 010-060) and circuit setter provided with optional pump package (factory-installed option)
  • GFI (ground fault interrupter) convenience outlet (factory-installed option)
  • Single-point electrical connection available on all sizes. Dual point electrical connection available on sizes 070-150.
  • Integral control transformer
  • Fluid loop storage tank designed to fit directly under unit (field-installed accessory on sizes 010-060)
  • On-the-ground or rooftop installation
  • Standard Limited Warranty
  • 3 year coil parts only on Novation microchannel heat exchanger
  • One year from start-up or 18 months from shipment on all other parts
  • Extended warranty packages available

30RB AQUASNAP®

Outdoor, Air-Cooled Liquid Chiller
with Puron® Refrigerant (R-410A)
60 to 390 Nominal Tons

The AquaSnap 30RB chiller is an effective all-in-one package that is easy to install and easy to own. The chiller costs less to purchase and install and then operates quietly and efficiently. Value-added features include rotary scroll compression, Puron® refrigerant (R-410A), a quiet AeroAcoustic™ fan system, easy to use ComfortLink™ controls, microchannel condenser coil technology, optional integrated hydronic pump package (with or without VFD) and optional full

  • Full-load EER values up to 9.7
  • IPLV values up to 14.2
  • ASHRAE 90.1 complaint
  • AHRI certified
  • Easy to use controls
  • AeroAcoustic fan system
  • Operation from -20 F to 125 F ambient conditions
  • High-efficiency scroll compressors
  • Novation® microchannel heat exchanger (MCHX) condenser coils
  • E-coated Novation microchannel heat exchanger (MCHX) condenser coils (factory-installed option)
  • Hydronic pump package (with or without VFD) on sizes 060-190 (factory-installed option, but N/A with heat recovery option)
  • Full heat recovery (factory-installed option, but N/A with hydronic package)
  • Energy Management Module minimizes chiller energy consumption (factory-installed option or field-installed accessory)
  • Non-fused disconnect switch (factory-installed option)
  • Minimum load control (factory-installed option or field-installed accessory)
  • Low ambient head pressure control (factory-installed option or field-installed accessory)
  • ComfortLink™ controls with scrolling marquee display module
  • BACnet* communication (factory-installed option) or BACnet and LON translator control (factory-installed option or field-installed accessory)
  • EXV (electronic expansion valve)
  • Navigator™ or Touch Pilot™ display (field-installed accessory)
  • ASME constructed evaporators
  • ETL (and ETL Canada) listed
  • Manufacturing facility registered to ISO 9001 manufacturing quality standard
  • Minimum of 2 independent refrigerant circuits
  • Factory full-load run tested
  • Heavy-gage galvanized steel frame
  • Security grilles (factory-installed option or field-installed accessory)
  • Hail guards/Privacy screen choices (factory-installed option or field-installed accessory)
  • Low ambient head pressure control (factory-installed option or field-installed accessory)
  • E-coated MCHX coil protection (factory-installed option)
  • Redundant pump available with hydronic pump package (sizes 060-190; factory-installed option)
  • Coil corrosion coatings available on all coil types (factory-installed option)
  • High short circuit current rating (factory-installed option)
  • EXV (Electronic expansion valve)
  • Permanently lubricated fan motor bearings
  • Over 15 diagnostic functions
  • Compressor suction service valves (factory-installed option)
  • GFI (ground fault interrupter) convenience outlet (part of factory-installed service option or field-installed accessory)
  • Microchannel condenser coils with inherent corrosion resistance and offering simplified cleaning (factory-installed option)
  • Unit-mounted, non-fused disconnect (factory-installed option)
  • Remote service port for easier machine diagnostics (factory-installed option or field-installed accessory)
  • Factory charged with Puron refrigerant (R-410A)
  • All-in-one package
  • Integrated hydronic pump package (with or without VFD) on sizes 060-190 (factory-installed option, but N/A with heat recovery option)
  • Full heat recovery (factory-installed option, but N/A with hydronic package)
  • GFI (ground fault interrupter) convenience outlet (part of factory-installed service option or field-installed accessory)
  • Remote cooler kit (field-installed accessory)
  • Extended warranty packages available
  • 3 year coil parts warranty on microchannel heat exchanger
  • One year from start-up or 18 months from shipment limited warranty
  • Standard Warranty
  • Circuit setter provided with optional pump package (factory-installed option)
  • Structurally robust base
  • Integral control transformer
  • Single or dual-point electrical connections available (factory-installed option)